intelligent power devices (ipds) 1 publication date: september 2001 slb00029aed MIP512 (tentative) silicon mosfet type integrated circuit features ? built-in five protection functions (over-current, over-voltage, load- short-circuit, over heat, esd) ? both dc and ac power suply are available applications ? lamp solenoid, and led drive for amusement machine ? motor, relay drive for factory automation absolute maximum ratings t c = 25 c 3 c parameter symbol rating unit drain-source voltage v ds 45 v output current i o 2.0 a input voltage v in ? 0.5 to + 6.0 v input current i in 10 ma power dissipation * p d 1.0 w operating ambient temperature t opr ? 40 to + 85 c channel temperature t ch 150 c storage temperature t stg ? 55 to + 150 c block diagram marking symbol: MIP512 unit: mm 1 : in 2 : drain 3 : source mt-2-a1 package drain source over voltage protection load short-circuit protection gate cut-off circuit esd protection over current protection over heat protection in note) * : the value at mounting on the printed circuit board (glass epoxy board: 100 mm 100 mm). (t a = 25 c) 6.9 0.1 2.5 0.1 0.45 1.05 0.05 2.5 0.5 123 2.5 0.5 +0.10 ?0.05 0.45 +0.10 ?0.05 (0.8) (0.5) (1.0) (1.0) 4.5 0.1 14.5 0.5 4.0 0.7 0.65 max. (0.2) this product complies with the rohs directive (eu 2002/95/ec). maintenance/ discontinued maintenance/discontinued includes following four product lifecycle stage. planed maintenance type maintenance type planed discontinued typed discontinued type please visit following url about latest information. http://panasonic.net/sc/en
MIP512 2 slb00029aed electrical characteristics t c = 25 c 3 c parameter symbol conditions min typ max unit drain-source on resistance r ds(on) v in = 5 v, i ds = 1 a 0.30 0.45 ? drain-source voltage v ds(on) v in = 5 v, i ds = 1 a 0.30 0.45 v drain clamp voltage v ds(clp) v in = 0 v, i ds = 3 ma 45 52 v drain off current 1 i ds(off)1 v in = 0 v, v ds = 12 v 5 20 a drain off current 2 i ds(off)2 v in = 0 v, v ds = 25 v 21 50 a drain off current 3 i ds(off)3 v in = 0 v, v ds = 40 v 55 120 a high level input voltage v in(h) i ds = 1 a 4 v low level input voltage v in(l) i ds = 1 ma 0.8 v input current (normal state) i in(on) v in = 5 v, v ds = 0 v 0.2 0.5 ma input current (protecting state) * i in(prot) v in = 5 v 0.45 1.00 ma over current limit value i ocp v in = 5 v 3.5 5.0 a load short-circuit detection voltage v ds(sht) v in = 5 v 2 4 v note) 1. when the drain voltage is more than load shot-circuited detection voltage at the output on state, output current oscilla tes. 2. when a drain voltage rises above a drain clamp voltage (over-voltage protection operating voltage), the output mos turns on and the drain voltage is clamped before breaking down between drain and source. *: the current value at the time when the load short-circuit protection and the over-heat protection are operating (for guarantee on design). electrical characteristics (reference value) parameter symbol conditions min typ max unit cut-off temperature at overheat t shd v in = 5 v 140 c note) 1. the above characteristic is for the reference and is not guarantee value. 2. when the chip surface temperature rise above the shutdown temperature at the over- heat, the output is shut down. when the chip surface temperature falls, operation starts again. this product complies with the rohs directive (eu 2002/95/ec).
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. no license is granted in and to any intellectual property right or other right owned by panasonic corporation or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20090106 p r e c a u t i o n s o n t h e s a l e s o f i p d s a t t a c h e d t a b l e " i p d a v a i l a b i l i t y b y c u s t o m e r " 1 ) t h e s a l e a n d / o r t h e e x p o r t o f i p d p r o d u c t s t o a n y c u s t o m e r o r c u s t o m e r s l o c a t e d i n a n y c o u n t r y o t h e r t h a n j a p a n i s e x p r e s s l y p r o h i b i t e d b y t h e a g r e e m e n t m a d e a n d e x e c u t e d b y a n d b e t w e e n p o w e r i n t e g r a t i o n s , i n c . a n d p a n a s o n i c c o r p o r a t i o n . 2 ) i p d p r o d u c t s p u r c h a s e d f r o m o u r c o m p a n y , o r i t s a u t h o r i z e d a g e n t s , h e r e i n a f t e r r e f e r r e d t o a s o u r c o m p a n y , s h a l l b e u s e d o n l y f o r p r o d u c t i o n p u r p o s e s b y t h o s e p a r t i e s w h o h a v e d u l y p u r c h a s e d i p d p r o d u c t s . t h o s e w h o h a v e p u r c h a s e d i p d p r o d u c t s s h a l l n o t u s e s u c h i p d p r o d u c t s i n u n m o d i f i e d f o r m f o r r e - s a l e , l o a n , o r s a m p l e s h i p m e n t f o r e v a l u a t i o n p u r p o s e s t o a n y o t h e r p a r t i e s . 3 ) i f a p a r t y w h o h a s d u l y p u r c h a s e d i p d p r o d u c t s s u b c o n t r a c t s i t s p r o d u c t i o n t o a n y o t h e r p a r t i e s , i n c l u d i n g i t s s u b s i d i a r i e s o r a n y o t h e r t h i r d p a r t i e s i n s i d e a n d / o r o u t o f j a p a n , a n d t h e i p d p r o d u c t s a r e c o n s i g n e d t o s u c h s u b c o n t r a c t i n g p a r t i e s t h e r e a t , s u c h p a r t y i s o b l i g a t e d t o m o n i t o r a n d c o n t r o l t h e q u a n t i t y o f i p d p r o d u c t s t o p r e v e n t a n y o f t h e a f o r e m e n t i o n e d r e - s a l e , l o a n o r s a m p l e s h i p m e n t s f r o m t a k i n g p l a c e . 4 ) i n t h e e v e n t t h a t a n y a c t u a l o r t h r e a t e n e d b r e a c h o r v i o l a t i o n o f a n y o f t h e a b o v e m e n t i o n e d 1 , 2 , o r 3 , h a s o c c u r r e d o r i s a b o u t t o o c c u r , o u r c o m p a n y w i l l h o l d a l l s h i p m e n t s o f i p d p r o d u c t s a n d m a y r e q u e s t t h e p a r t y a l l e g e d t o b e r e s p o n s i b l e f o r s u c h o c c u r r e n c e f o r n e c e s s a r y . n o t e ) t h e p r o d u c t s o f m i p 5 0 , m i p 5 1 , a n d m i p 7 a r e e x c l u d e d f r o m a b o v e - m e n t i o n e d p r e c a u t i o n s , 1 ) t o 3 ) . a p p l i c a t i o n f o r p o w e r s u p p l y f o r d c - d c c o n v e r t e r f o r p o w e r s u p p l y f o r e l d r i v e r f o r l e d l i g h t i n g d r i v e r f o r l a m p d r i v e r / c a r e l e c t r o n i c s a c c e s s o r i e s c o m p a n i e s / a r e a s t o w h i c h p r o d u c t s c a n n o t b e s o l d c o m p a n i e s i n e u r o p e a n a n d a m e r i c a n c o u n t r i e s a s i a n c o m p a n i e s i n a s i a o t h e r l o c a l c o m p a n i e s c o m p a n i e s i n e u r o p e a n a n d a m e r i c a n c o u n t r i e s o t h e r l o c a l c o m p a n i e s n o r e s t r i c t i o n s i n t e r m s o f c o n t r a c t c o m p a n i e s / a r e a s t o w h i c h p r o d u c t s c a n b e s o l d j a p a n e s e c o m p a n i e s i n j a p a n j a p a n e s e c o m p a n i e s i n a s i a ( 5 0 % o r m o r e o w n e d ) j a p a n e s e c o m p a n i e s i n j a p a n j a p a n e s e c o m p a n i e s i n a s i a ( 5 0 % o r m o r e o w n e d ) a s i a n c o m p a n i e s i n a s i a n o r e s t r i c t i o n s i n t e r m s o f c o n t r a c t m i p 1 3 m i p 1 4 m i p 1 5 m i p 1 6 m i p 1 0 m i p 1 1 m i p 8 0 3 / 8 0 4 / 8 0 6 m i p 9 e m i p 5 0 m i p 5 1 n o t e ) if you have any inquiries about sales, contact corporate marketing & sales division of our company . p a r t s n o . m i p 1 7 m i p 2 m i p 1 8 m i p 3 m i p 0 1 m i p 4 m i p 0 2 m i p 9 a m i p 8 1 1 / 8 1 2 m i p 8 1 4 / 8 1 5 / 8 1 6 m i p 8 2 m i p 5 5 m i p 7
|
